Step 1: Chiller Placement

/!\ DANGER: Risk of electric shock. Install at least 1.5 meters (5 feet), from all electrical outlets and appliances.

• Make sure the Plunge and the Chiller are on a solid, flat, waterproof surface.
• Locate where the chiller connections will connect to the tub.
• Place the chiller on the end with the circular fan facing out and about 4 inches from the tub. Note: Make sure there is at least 16 inches between the chiller fan and the wall to allow for ventilation; not doing so will void your warranty.

Plunge Evolve XL

Plunge Air

Plunge Pop-Up

Plunge Pod

Step 2: Connecting the Tub

• Find connection A
• Check to make sure the black O-ring is seated in the connection collar.
• Connect it to the drain port on the tub indicated in the image. Tighten the collar until it is hand-tight. 
• Find connection B
• Check to make sure the black O-ring is seated in the connection collar.
• Connect it to the jet port on the tub indicated in the image. Tighten the collar until it is hand-tight.

Please make sure the threading is on straight and not cross-threaded. Cross-threading can damage the connection collars. The connection collar should turn with ease. 

Evolve XL

Plunge Air

Plunge Pop-Up

Plunge Pod

Step 3: Connecting the Chiller

• Grab connection A and check to make sure the black O-ring is seated in the connection collar.
• Connect connection A to the drain port on the chiller indicated in the image. 
• Grab connection B and check to make sure the black O-ring is seated in the connection collar. 
• Connect connection B to the jet port on the chiller indicated in the image.

Please make sure the threading is on straight and not cross-threaded. Cross-threading can damage the connection collars. The connection collar should turn with ease. 

Evolve XL


Plunge Air

Plunge Pop-Up

Plunge Pod

Step 4: Fill the Plunge

• Attach the included carbon hose filter to a garden hose.
• Run water through it into a drain until the water turns clear.
• Then, fill the interior of the Plunge with water until it reaches 5 inches from the top.
• Please note: If you have the Plunge Pod, make sure the safety strap is installed before filling the tub.

Step 5: Plug in the Evolve Pro Chiller

/!\ WARNING: Only plug your Evolve Pro Chiller into a dedicated 120V 15A 2 wire plus ground service outlet with a GFCI plug.  The term “dedicated” means that the electrical circuit for the Plunge is not being used for any other electrical items.  The electrical supply for this product must include a suitable 15A circuit breaker. The plug must be readily accessible and visible to the Plunge occupant but installed at least 1.5 meters (5 feet), from the Plunge water.

• Once the tub is full you can plug in your Plunge to a dedicated 15 amp Circuit (120V). 
• Ensure the Evolve Pro Chiller has rested for at least 20 minutes for the coolant to settle before plugging it into the outlet.
• Note: If you plan to use an extension cord, it needs to be 12 gauge to give the Plunge sufficient power up to 25ft. Please follow all NEC requirements.

   

Step 6: Turning the Plunge On

• Locate the two buttons on the power cord that say “test” and “reset”.
• Press the “reset” button to turn it on.
• You should hear the jets turn on and see the screen on the chiller light up with the current temperature.

Step 7: Set your Temperature

• Press the up and down arrows on the back of the tub to set your desired temperature. 
• The blue arrow indicates cooling, and the red arrow indicates heating. 

Step 8: Operate Light

For Plunge Evolve XL Tubs Only

• The plug for the light should be taped onto the side of the tub when it arrives.
• Remove the tape and unwind the plug.
• Plug the light into the location indicated in the image below. 
• To operate the light, just press the button with the light bulb to turn it on and press it. again to turn it off. Note: The light will automatically turn off after four hours.

Step 9: Pausing the Jets

• For a quieter Plunge experience, you can pause the jets by pressing the pause button. 
• It will pause in increments of 15 minutes up to an hour. 
• Once the timer runs out, the jets will turn back on and resume circulating the water.

Step 10: Water Maintenance 

Please go here to purchase your water maintenance kit for your Evolve Pro Chiller. 

Step 11: Take the Plunge, and get ready to change your life!